Feature 8 of 10, Network cameras.
Cameras round the room, and from anywhere.
IP cameras on your network over RTSP and ONVIF, or a guest anywhere in the world over SRT. CamStation finds them and checks each one before it goes on air, with no extra software.

Find, log in, check

Found on the network, by itself.
Add › Network Camera… asks every camera on your network to answer, over ONVIF, for about ten seconds, and lists the ones that do with their name and address. Choose yours and type its login: under the password, a line says what that maker’s cameras usually expect. Once you’re in, its snapshot appears, so you can tell which camera is which.
Not in the list? Some Wi-Fi networks hide devices from a search, and
some cameras answer only once ONVIF is switched on in their app. Type Its Address… takes a bare address, a full rtsp:// link from the camera’s manual, or an srt:// link, takes any login out of it for
the Keychain, and asks the camera where its stream is.
A camera you add is a camera that works.
Then CamStation connects exactly as it will on air and shows the picture live, with its sound on a meter and what arrives: the size, the codec, the delay and whether it comes from this network or the internet. Add Camera stays off until the picture is live.
On air, a network camera is a camera like any other: a card you cut to, with its sound in the mix, or a layer in a composite.
Give each camera a fixed address in your router (a DHCP reservation). Otherwise a camera can come back from a power cut with a new address, and the show can’t find it.

A camera somewhere else
A guest across town, over SRT.
For a camera that isn’t on your network, such as a phone at another place, an encoder or a studio across town, choose A Camera Somewhere Else…. CamStation receives it over SRT, the protocol made for sending a picture across the internet: it recovers lost pieces within a time budget and encrypts the stream with a passphrase.
Most of the time the phone or encoder sends to your Mac, and CamStation shows exactly what to type into it: your public address, the port, a passphrase made of words and a number, the mode, and the whole link to paste into OBS or ffmpeg. It can also fetch the picture from a relay server, or meet the sender halfway in rendezvous mode when both sides are behind routers nobody can change, such as an office, a hotel or mobile data.
Keep a safe shot. A remote guest on mobile data can drop at any moment. In every scene that uses a remote source, keep a card ready to cut to (the host camera, a two-shot, the stand-in) and know its key before the guest goes live.
Latency or smoothness
A picture crossing a network doesn’t arrive at an even pace, so CamStation holds every piece for a moment, long enough for the late ones to catch up. How long it waits is the camera’s Latency, and you choose it for each camera.
Lowest
The default: the least wait that kept every piece of the last minute on time. For a camera on someone you’re talking with live.
Balanced
About twice that, and it rides out a Wi-Fi network’s hiccups.
Smooth
About half a second on your network, about a second over SRT, for the smoothest picture. For a camera only watched, never talked to, like a wide shot of the room.
A lost piece never reaches the program.
A piece lost on the network is never shown half-drawn: the last good picture stays until the next whole one arrives. The SOURCE tab counts what was lost, and since when, so you know which camera to look at after the show.
Cable beats Wi-Fi, always. A network cable to a camera, often carrying its power too (PoE), gives a picture that arrives evenly and lets you run it at Lowest. If a camera must be on Wi-Fi, give it a strong 5 GHz signal and choose Balanced.
Steady on air
Every state, said on the card.
UNSTABLE means the picture is live but lost pieces in the last minute: try the camera’s smaller Sub stream or Balanced latency. You can still cut to it. RECONNECTING means it dropped and CamStation is retrying by itself, sooner at first, then every 30 seconds. OFFLINE comes with the reason in plain words and what fixes it.
The decision stays yours.
A camera that drops while on air holds its last frame on the program. The top display warns ⚠ OFFLINE with the camera’s name and the time since it was lost, and the program monitor tags the picture LAST FRAME, for you only. Cut to another card or press STAND-IN: CamStation never switches away on its own.
Turn off the sound of every camera you don’t use as a microphone. A camera’s built-in mic across the room hears the room’s echo and arrives after your real mics; mixed in, it makes your voice sound hollow. See Sound for what to use instead.
At a glance
- Protocols
- RTSP and RTSPS (over UDP or TCP), ONVIF for finding cameras and their streams, SRT for cameras over the internet.
- Video
- H.264 and H.265 (H.264+ and H.265+ too). Decoded by your Mac’s media engine.
- Sound
- AAC, G.711 and Opus.
- SRT
- Caller, listener and rendezvous; a passphrase for AES encryption; a stream ID for servers that ask for one.
- Latency
- Lowest, Balanced or Smooth, per camera. A lost piece holds the last good picture.
- Streams
- Main or Sub, for cameras that offer both; transport Auto (UDP, then TCP) or TCP.
- Health
- LIVE, UNSTABLE, RECONNECTING, OFFLINE on the card; picture, codec, data rate, jitter, delay and losses on the SOURCE tab.
- Logins
- Kept in this Mac’s Keychain; a camera’s own certificate can be trusted by its fingerprint.
- Not yet
- NDI, WebRTC, and moving a PTZ camera from CamStation.
- Tier
- Part of CamStation Free. A network camera as a layer of a composite shot needs Pro, as any composite does.
Questions
Which cameras work?
Any camera that serves RTSP or RTSPS with H.264 or H.265 video, which is almost every IP and PTZ camera. Cameras that speak ONVIF are found on the network by themselves; the others are added by typing their address.
Can a guest send their camera from somewhere else?
Yes, over SRT: a phone running an app such as Larix, OBS, an encoder or another studio. CamStation shows the sender exactly what to type, with a passphrase that encrypts the picture, and supports caller, listener and rendezvous modes for the usual router setups.
What happens if a camera drops while it’s on air?
The program holds its last frame, the display warns OFFLINE with the camera’s name and the time since it was lost, and CamStation reconnects by itself. It never cuts away on its own: you choose the shot to go to.
Does CamStation support NDI?
Not yet. Network cameras come in over RTSP, RTSPS, ONVIF and SRT. Moving a PTZ camera from CamStation isn’t built yet either: frame it with the camera’s own app or remote.
Do I need extra software?
No. CamStation receives the streams itself and decodes them on your Mac’s media engine.
Read on
Your show, on your Mac, the way broadcast does it.
Be the first to know when the beta opens.




